Les inscriptions pour le Meeting National sont ouvertes ici
Participation au calendrier 2025 du Club : concourez ici
Participation au calendrier 2025 du Club : concourez ici
Amélioration endurance freinage Z4M
- extremex
- habitué
- Messages : 3846
- Inscription : 18 janv. 2007
- Département : 95 Val-d'Oise
- Véhicule : Z4 Roadster 3.0si
Re: Amélioration endurance freinage Z4M
Faut déjà y aller fort avec les RS29 + Durits avia + RBF600 pour manquer d'endurance sur route...
Z4 3.0 > Z4 3.0 SI > Z4 3.0 SI > Z4M > Z4 3.0 SI
- ZZ4444
- habitué
- Messages : 1751
- Inscription : 23 mai 2009
- Département : Luxembourg
- Véhicule : Z4 M Roadster
- Localisation : Luxembourg
Re: Amélioration endurance freinage Z4M
Non mais je parlais de refroidissement, pas d'endurance. Pour pas abimer le disque quoi. Mais je crois que y a un autre sujet specifique au refroidissement et là je suis sur endurance, oups.
- morkenultor
- CorreZpondant
- Messages : 7190
- Inscription : 10 févr. 2007
- Localisation : 13 Délégué Régional PACA
Re: Amélioration endurance freinage Z4M
Dernière modification par morkenultor le sam. 25 févr. 2017, 08:17, modifié 1 fois.
Les choses qu’on possède finissent par nous posséder
http://www.youtube.com/watch?v=rBexpeHVH_g
https://www.youtube.com/watch?v=KJ5miTHZXV8
http://www.youtube.com/watch?v=rBexpeHVH_g
https://www.youtube.com/watch?v=KJ5miTHZXV8
- morkenultor
- CorreZpondant
- Messages : 7190
- Inscription : 10 févr. 2007
- Localisation : 13 Délégué Régional PACA
Re: Amélioration endurance freinage Z4M
Qui aurait eu l'occasion de tester des Ferodo ds 1 . 11? voir les ds uno. Merci
si je m'amuse a tout comparer
en comparaison les pagid deux dispos rs29 No. 8084 et rsl1
CL
RC5+ - average friction coefficient µ= 0,4. The newest compound in our range, the RC5+, was developed for light weight vehicles or racing in low grip conditions (street tires, gravel, mud, snow, water, etc.). An excellent track day compound, it offers moderate friction levels, low noise, is easy on OEM discs, and has excellent cold stopping power. Additionally, it can be used on the rear axle of vehicles to change the brake bias where standard bias adjustment is not possible.
RC6 - average friction coefficient µ= 0,4. Our original compound, RC6 was designed to apply to a wide range of motorsports, from rally to circuit. It has a high and very flat friction level and can be used successfully in almost every type of race car. Low compressibility provides a stiff pedal which greatly increases feedback and allows for easier modulation. It can also be used in the front or rear axle combined with the RC8 or RC5 to adjust bias.
RC6E - average friction coefficient: µ=0,46. New in 2008, the RC6 Endurance was designed to offer very low pad and disc wear rates without sacrificing friction levels. Need pads to last 6, 12 or even 24, hours. Look no further than the RC6E. The RC6E boasts the same easy bed-in and stable friction levels as all other CL Brakes compounds.
RC8 - average friction compound: µ=0,6. Developed in 2006, the RC8 compound boasts CL Brakes highest friction level and is used in top-tier motorsports such as WRC, WTCC, NASCAR, ZA V8, AWD GrpN, etc. Extremely high friction levels allow shorter stopping distances and the flat torque curve provides excellent modulation to prevent wheel lockup.
RC8R - average friction compound: µ=0,6. Using the same friction material as our standard RC8, we have grooved the backing plate to reduce the contact area with the piston and provide a radiator effect. This patented shape was created to reduce heat transfer through the piston and into the brake fluid.
hawk
Mintex
EBC
carbon kevlar
si je m'amuse a tout comparer
en comparaison les pagid deux dispos rs29 No. 8084 et rsl1
CL
RC5+ - average friction coefficient µ= 0,4. The newest compound in our range, the RC5+, was developed for light weight vehicles or racing in low grip conditions (street tires, gravel, mud, snow, water, etc.). An excellent track day compound, it offers moderate friction levels, low noise, is easy on OEM discs, and has excellent cold stopping power. Additionally, it can be used on the rear axle of vehicles to change the brake bias where standard bias adjustment is not possible.
RC6 - average friction coefficient µ= 0,4. Our original compound, RC6 was designed to apply to a wide range of motorsports, from rally to circuit. It has a high and very flat friction level and can be used successfully in almost every type of race car. Low compressibility provides a stiff pedal which greatly increases feedback and allows for easier modulation. It can also be used in the front or rear axle combined with the RC8 or RC5 to adjust bias.
RC6E - average friction coefficient: µ=0,46. New in 2008, the RC6 Endurance was designed to offer very low pad and disc wear rates without sacrificing friction levels. Need pads to last 6, 12 or even 24, hours. Look no further than the RC6E. The RC6E boasts the same easy bed-in and stable friction levels as all other CL Brakes compounds.
RC8 - average friction compound: µ=0,6. Developed in 2006, the RC8 compound boasts CL Brakes highest friction level and is used in top-tier motorsports such as WRC, WTCC, NASCAR, ZA V8, AWD GrpN, etc. Extremely high friction levels allow shorter stopping distances and the flat torque curve provides excellent modulation to prevent wheel lockup.
RC8R - average friction compound: µ=0,6. Using the same friction material as our standard RC8, we have grooved the backing plate to reduce the contact area with the piston and provide a radiator effect. This patented shape was created to reduce heat transfer through the piston and into the brake fluid.
hawk
Mintex
EBC
carbon kevlar
Dernière modification par morkenultor le ven. 16 juin 2017, 03:39, modifié 13 fois.
Les choses qu’on possède finissent par nous posséder
http://www.youtube.com/watch?v=rBexpeHVH_g
https://www.youtube.com/watch?v=KJ5miTHZXV8
http://www.youtube.com/watch?v=rBexpeHVH_g
https://www.youtube.com/watch?v=KJ5miTHZXV8
- extremex
- habitué
- Messages : 3846
- Inscription : 18 janv. 2007
- Département : 95 Val-d'Oise
- Véhicule : Z4 Roadster 3.0si
Re: Amélioration endurance freinage Z4M
Un ami en ds uno sur sa s3 300cv est satisfait pour usage sportif sur route, mais au Nurb, ca fumait sec !
Z4 3.0 > Z4 3.0 SI > Z4 3.0 SI > Z4M > Z4 3.0 SI
- morkenultor
- CorreZpondant
- Messages : 7190
- Inscription : 10 févr. 2007
- Localisation : 13 Délégué Régional PACA
Re: Amélioration endurance freinage Z4M
j'ai trouvé ces courbes sur un forum corvette . et je ne sais pas quelle choit faire entre ds uno ou 1.11 pour de la montagne avec un touché qui rende moins "spongieux" à la pression.
Dernière modification par morkenultor le sam. 21 janv. 2017, 23:07, modifié 2 fois.
Les choses qu’on possède finissent par nous posséder
http://www.youtube.com/watch?v=rBexpeHVH_g
https://www.youtube.com/watch?v=KJ5miTHZXV8
http://www.youtube.com/watch?v=rBexpeHVH_g
https://www.youtube.com/watch?v=KJ5miTHZXV8
- extremex
- habitué
- Messages : 3846
- Inscription : 18 janv. 2007
- Département : 95 Val-d'Oise
- Véhicule : Z4 Roadster 3.0si
Re: Amélioration endurance freinage Z4M
Achete DES performance friction, un must
Z4 3.0 > Z4 3.0 SI > Z4 3.0 SI > Z4M > Z4 3.0 SI
-
- habitué
- Messages : 23369
- Inscription : 09 avr. 2007
- Département : Groland
- Véhicule : En cours
- Localisation : WC
Re: Amélioration endurance freinage Z4M
Les PFC sont très bien, à ceci près que sur un setup complet avant/arrière, les ressorts de maintien dans le piston des plaquettes arrières cassent et la plaquette va bouger dans l'étrier ce qui est pénible (bruit). Une solution c'est un point de soudure pour fixer plus solidement le ressort à la plaquette.
- Ferny - ManoucheClub
- morkenultor
- CorreZpondant
- Messages : 7190
- Inscription : 10 févr. 2007
- Localisation : 13 Délégué Régional PACA
Re: Amélioration endurance freinage Z4M
j'ai connu le même probleme sur des ds2500 à l'arriere. J'avais du mal faire le point de soudure ça à laché. Du coup javais opté pour des pagid bleus, diablement efficaces mais bruyantes et agressives.
(chez ARS les ferodo 1.11 avant pour etrier M135i sortent à 198e.)
Merci de vos pistes je vais voir cela
(chez ARS les ferodo 1.11 avant pour etrier M135i sortent à 198e.)
Merci de vos pistes je vais voir cela
Les choses qu’on possède finissent par nous posséder
http://www.youtube.com/watch?v=rBexpeHVH_g
https://www.youtube.com/watch?v=KJ5miTHZXV8
http://www.youtube.com/watch?v=rBexpeHVH_g
https://www.youtube.com/watch?v=KJ5miTHZXV8
-
- habitué
- Messages : 23369
- Inscription : 09 avr. 2007
- Département : Groland
- Véhicule : En cours
- Localisation : WC
Re: Amélioration endurance freinage Z4M
Avec les PFC par contre, poussière de frein vraiment abondante... à ne pas laisser sur les jantes trop longtemps sinon la peinture morfle !
- Ferny - ManoucheClub
- extremex
- habitué
- Messages : 3846
- Inscription : 18 janv. 2007
- Département : 95 Val-d'Oise
- Véhicule : Z4 Roadster 3.0si
Re: Amélioration endurance freinage Z4M
Pas eu ce pb moi...ferny37 a écrit :Les PFC sont très bien, à ceci près que sur un setup complet avant/arrière, les ressorts de maintien dans le piston des plaquettes arrières cassent et la plaquette va bouger dans l'étrier ce qui est pénible (bruit). Une solution c'est un point de soudure pour fixer plus solidement le ressort à la plaquette.
Z4 3.0 > Z4 3.0 SI > Z4 3.0 SI > Z4M > Z4 3.0 SI
- morkenultor
- CorreZpondant
- Messages : 7190
- Inscription : 10 févr. 2007
- Localisation : 13 Délégué Régional PACA
Re: Amélioration endurance freinage Z4M
plus qu'a choisir les plaquettes et leur coef de friction en fonction de leur plage d'utilisation (T°C/Friction) par rapport à la température au niveau des disques/étriers. En pensant ne pas trop déséquilibrer AV/ AR avec les coef de friction j'opte pour des pagid à lavant / ferrodo ar.
petit lien qui recense toutes les plaquettes du marché en 2017
https://www.a3forum.fr/trains-roulants- ... 40937.html
Les choses qu’on possède finissent par nous posséder
http://www.youtube.com/watch?v=rBexpeHVH_g
https://www.youtube.com/watch?v=KJ5miTHZXV8
http://www.youtube.com/watch?v=rBexpeHVH_g
https://www.youtube.com/watch?v=KJ5miTHZXV8